Current position: Products -100M series

16E1/4ETH converter

 16E1 / 4ETH protocol converter uses reverse multiplexing, multi E1 circuits tied up for Ethernet data transmission 10M / 100M, to achieve the mutual conversion 1~16 road E1 channel to Ethernet interfaces between this E1 channel converter can send and receive signals point to point transmission to the RJ45 interface to interconnect E1 channel and Ethernet. And the general remote bridge is different, this converter supports flexible configuration 1~16 road E1 channels can automatically detect the number of E1 and select the available E1, and allows certain transmission delay difference between E1 circuits. Single line rate is 1968Kbit / s, 4-way bandwidth of up 7872Kbit / s. Each Ethernet can be isolated when the device is used in 10 / 100Mbps full / half duplex mode, it can be connected to an Ethernet switch or hub, make full use of the large number of existing telecommunications network resources to extend E1 circuits Ethernet transmission Distance and applications, Ethernet broadband access a good solution. This product can be used in various fields LAN interconnection, interconnection infrastructure, video on demand, remote monitoring, switch E1 interface card and so on.

The protocol converter is a high performance, adaptive remote Ethernet bridge. Its small size, low cost, it is suitable for cost-sensitive bridging applications or as a LAN extender or segmented basis of bitstream structure. Widely used in between WAN and LAN networking, monitoring and other occasions.


□ based on proprietary integrated circuit;

□ Ethernet data transparent transmission in 1 to 16 E1 circuits;

□ Ethernet interface 10M / 100M, full / half duplex fully adaptive, support VLAN protocol;

□ Each port supports Ethernet support AUTO-MDIX (crossover cable and straight-line adaptive);

□ CRC alarm thresholds can be set automatically to poor transmission quality of the line were isolated and cut off in one direction;

□ Allow 4 E1 transmission delay of 10ms difference there. When the difference exceeds the allowable range, the system can automatically stop sending the delay is too large E1;

□ 4-way 10M / 100M Ethernet interface isolated from each other and achieve independence communications;

□ E1 interfaces and four Ethernet interface has lightning protection;

□ E1 interface complies with ITU-T G.703, G.704 and G.823, do not support the use of signaling slots;

□ E1 interface module with built-in clock recovery circuit and HDB3 codec circuit;

□ device to work in support of E1 channel hot-swappable, and automatically detects effective E1 channels data transmission will not be interrupted in the middle;

□ support flexible configuration 1-4 E1 channels in reset automatically detect the number of E1 and delay and select the available E1;

□ support desktop, 1U high 19-inch rack-mount, 4U chassis card type;

□ support SNMP network management;

E1 Interface

Equipment E1 interface comply with G.703

Rate: N * 64Kbps (framing) or 2048Kbps ± 50ppm (non frame)

Pattern: HDB3

Impedance: Unbalanced 75W / 120W balanced

      Unbalanced with coaxial adapter, which can be adapted to 75-2 / 3 coaxial

Jitter characteristics: meet G.742, G.823 recommendation

Allows input attenuation: 0∽6dBm

Ethernet interface (10 / 100M)

Rate: 10 / 100MM adaptive, full / half duplex fully adaptive

Agreement: support IEEE 802.3, IEEE 802.1Q (VLAN)

MAC address table: 4096 MAC addresses can be learned

Physical interface: RJ45 seat support (cross / straight-line adaptive) Auto-MDIX

Power requirements

System Power: AC180V ~ 260V;

    DC -48V;

    DC + 24V

working environment

Working temperature: -10 ℃ ∽ ~ 50 ℃

Humidity: 5% ∽95% (non-condensing)

Storage temperature: -40 ℃ ∽80 ℃

Storage humidity: 5% ∽ 95% (non-condensing)

Contact:0571-81389112      Digital map | Contact us | Legal Description |     Copyright Hangzhou Xeikon Communication Technology Co., Ltd. All rights reserved. Zhejiang ICP No. 09064986